User manual for "Super ELD"

Super ELD
User Manual

contents
01
04
05
06
08
09

installing the eld in your vehicle
important first steps
getting set up on the app
pairing your eld with your device
automatic driving detection
basic app functions

14
15
16
17

dot inspection mode
troubleshooting
eld malfunction
help and support

Adding New Records....................09
Editing Existing Logs.....................10
DVIRS.................................................10
Reports..............................................13

Installing the ELD in Your Vehicle
First, locate the vehicles diagnostic port.
Generally, this port is found in 1 of 4 locations:

Plug ELD into diagnostics port.

Press until the clip snaps into place.
You will hear a click once it is plugged in.

If youre having trouble locating
this port, please refer to your
vehicles owner manual.

01

Attach the cable to your vehicles diagnostic port. Depending on your
vehicle, the required connector or adapter(s) may be different. A quick
glance at your diagnostic port will make this clear:
A OBD-2 16-pin

1

Holding the ELD, identify the flat, single cable
plugged into it from the previous step.

2 Keeping that plugged in, grab the other end of the
cable and connect it to your OBD-1/16-pin port.
16-Pin with Adapter Only:
1. Plug flat cable into ELD, then plug 9-pin green
into 9-pin black adapter and lock the green collar.
2. Plug 16-pin black into the vehicle.

B

9-pin

1

Holding the ELD, identify the flat, single cable
plugged into it from earlier.

2 The other end of this cable - the green, circular
side with a spinning, textured collar - will plug
into your vehicle.

3 Rotating the cable and collar if needed, plug
this into your vehicle.

4 After this is plugged in, tighten the collar by
turning it to lock the cable in place.

02

IMPORTANT FIRST STEPS

Once the ELD is plugged into your vehicle and secured on the dashboard
1

Make sure your engine is off and the ELD
is plugged into your vehicle. You will see
different blinking lights while the ELD is
establishing a GPS connection. Once the
LED status light shows only a blinking
green light, you can move onto step 2.
NOTE Some US models may need to turn their
ignition to ON or accessory power.

2

With the LED status light blinking only
green, double-check that:

3

Next, start your engine and the LED
status lights will change again. Wait for
a solid red and solid green LED light
displaying in unison.

4

Please note that the red light will
disguise the green light, so look closely
that both are on.
With both solid red and green LED
lights displayed, launch the Super
Dispatch app.

1) Your vehicle engine is off or on/accessory
2) Your phone or tablets bluetooth is off
3) If applicable, the Super Dispatch app is closed

03

Getting Setup on the Mobile Application
Before moving forward, double-check that
your phone or tablets bluetooth is turned
OFF. You can do this in your settings.
If you already have the Super Dispatch
app, check for an update in the App store
or Google Play Store. If one is available,
please download it now.

With the app now open, tap on the HoS
icon. This is where you can view your logs,
connect to an ELD, complete DVIRs and have
DoT officers inspect your logs.
Select your Home Terminals timezone. Your
logs will be based on this timezone. We also
support Canadian timezones.

If you do not have the app, or you are
checking for an update, enter the link
below into your browser to download it:
goo.gl/jZuw78
After updating or downloading the latest
version of the app, open it and sign up or
log in.

04

Select SPECIFY A VEHICLE

Pairing Your ELD with
Your Device

After you specify your vehicle, select
CONNECT TO ELD and you will see the
following prompts:

Select ALLOW to continue.
You need to input your vehicle information,
and when completed select DONE.

Enable bluetooth in settings.

Connect to your ELD by selecting the
device starting with PT30

05

If you do not find your ELD in this list,
then check:
1) That the ELD is plugged in
2) Your truck is turned on
If you continue to experience trouble,
contact [email protected]

If youre connected, you will see a green box in the
top right of HoS indicating this.
Alternatively, it will say not connected.
Once youre connected to the ELD with your phone
or tablet, you should see a green light on the ELD
hardware connected to your vehicle.
Youre all set!

Confirm youd like
to connect to this
specific device.

Once you connect,
you can go back
to the HoS home
screen.

06

Automatic Driving Detection
Once youve connected the ELD to your
vehicle, and your phone or tablet to the ELD,
your driving will automatically be recorded if
you accelerate over 5 mph.
1) While stationary, you can
indicate your status as a YARD
MOVE under ON DUTY. Personal
Conveyance is found under OFF
DUTY.

Being stationary for longer than five minutes
1) If the vehicle slows down to 0 mph for 5 consecutive minutes without any user interaction, a
pop up window will appear asking if you want to
change your status.

2) While driving over 5 mph, the
screen will display with a countdown for your hours.
3) You cannot change your status
while driving. To change status,
you must first be stationary.

2) If nothing is done, the device will set your status
from DRIVING to ON DUTY automatically.

07

Basic App Functions
Editing Hours of Service
A. If you need to edit a past duty status, you can
do this by selecting the day in your history

C. Tap the status you want to add.
D. Tap START TIME to specify the
beginning of the status hange.
Then, tap the green checkmark or
hit OK. Repeat this step for the end
time of your status addition.
E. Add your status details:
Add Location
Add notes
Its important to add detailed
notes on edits so that records
show why records have been
edited.

B. Tap ADD NEW RECORD within this specific day

F. Tap SAVE in the top right.

08

Editing an existing log

Do a Driver Vehicle Inspection Report (DVIR)

A. If you need to edit an exist

Read the full extracted text